ECU pin-out/Wiring diagram for 996
#1
ECU pin-out/Wiring diagram for 996
Anyone have one handy? I just need to find the pin location of 3 wires. Any help would be greatly appreciated!
TIA,
Shiv
TIA,
Shiv
Last edited by DJ; 12-08-2005 at 04:37 PM.
#2
Re: ECU pin-out/Wiring diagram for 996
Originally posted by Shiv@Vishnu
Anyone have one handy? I just need to find the pin location of 3 wires. Any help would be greatly appreciated!
TIA,
Shiv
Anyone have one handy? I just need to find the pin location of 3 wires. Any help would be greatly appreciated!
TIA,
Shiv
1 - Heating of HO2S after TWC
2 - Idle air control valve, closing coil
3 - Fuel injector, cylinder 1
4 - Fuel injector, cylinder 2
5 - Fuel injector, cylinder 3
6 - Ground point 9
7 - EVAP canister shutoff valve
8 - Check Engine MIL
9 - not assigned
10 - not assigned
11 - not assigned
12 - Crash signal (airbag)
13 - knock sensor 1 (cyl. 1-3)
14 - Medium pressure switch (A/C)
15 - Intake air temperature sensor
16 - Engine compartment temperature sensor
17 - Signal, mass air flow sensor
18 - Signal, H02S 2 ahead of TWC
19 - Signal, HO2S 1 ahead of TWC
20 - Ground, speed sender
21 - Signal, camshaft position sensor 1 + 2
22 - Ignition coil, cyl. 4 terminal 1
23 - Ignition coil, cyl. 3 terminal 1
24 - Ignition coil, cyl. 5 terminal 1
25 - Camshaft adjustment, bank 2
26 - Terminal 30
27 - Triggering of DME relay, terminal 85
28 - Ground, electronic system (shield)
29 - Idle air control valve opening coil
30 - Heating of HO2S ahead of TWC
31 - Fuel injector, cylinder 6
32 - Fuel injector, cylinder 4
33 - Fuel injector, cylinder 5
34 - Ground, sender
35 - Coolant fan, stage 1
36 - Coolant fan, stage 2
37 - Triggering of relay (terminal 85), secondary air pump
38 - Version coding (ground for Tiptronic)
39 - Fuel reserve pilot light
40 - not assigned
41 - Knock sensor 2 (cyl. 4-6)
42 - Automatic I/M test
43 - not assigned
44 - Signal, throttle position sensor
45 - Ground, mass air flow sensor
46 - Ground, oxygen sensors
47 - 5-volt supply for mass air flow sensor
48 - Nominal engine torque to TC control module
49 - Ignition coil, cyl. 1 terminal 1
50 - Ignition coil, cyl. 6 terminal 1
51 - Ignition coil, cyl. 2 terminal 1
52 - Camshaft adjustment, bank 1
53 - 5-volt supply, throttle position sensor
54 - Voltage supply for various components
55 - Ground, ignition
56 - Terminal 15
57 - not assigned
58 - Actual engine torque from TC control module
59 - Tuning flap (intake manifold switchover)
60 - Programming voltage
61 - EVAP canister purge valve
62 - A/C compressor On
63 - Triggering of fuel pump relay (terminal 85)
64 - not assigned
65 - Relay of engine compartment purge fan (terminal 85)
66 - Start-inhibit relay (terminal 85)
67 - not assigned
68 - Position switch/clutch switch
69 - A/C compressor requirement
70 - not assigned
71 - Ground, knock sensors
72 - Tank pressure sensor
73 - Oil temperature sensor
74 - Engine coolant temperature sensor
75 - not assigned
76 - Signal, H025 2 after TWC
77 - Signal, H025 1 after TWC
78 - Signal, rpm crankshaft position sensor
79 - Speed signal from ABS control module
80 - Speed signal output
81 - not assigned
82 - Coolant level
83 - Fuel gauge
84 - not assigned
85 - CAN low
86 - CAN high
87 - L wire
88 - K wire
#4
hi to all maybe anyone can help me with bentley continental gt.
i try restore two ecus master and slave. i write two full ori flashes.
car now start but only on left side engine and have fault p1924 control module pin coding/implausible signal.
p1923 check dtc memory of engine control module (ecm 2)
p0513 incorrect immobilizer key.
can anyone help me please?
i have
vag com
odis
thanks to all
i try restore two ecus master and slave. i write two full ori flashes.
car now start but only on left side engine and have fault p1924 control module pin coding/implausible signal.
p1923 check dtc memory of engine control module (ecm 2)
p0513 incorrect immobilizer key.
can anyone help me please?
i have
vag com
odis
thanks to all
#5
Hello,
The car now starts, but only on the left side, and there is an issue with the p1924 control module pin coding/implausible signal.
turkish citizenship
p1923 verify the engine control module's dtc memory (ecm 2)
The car now starts, but only on the left side, and there is an issue with the p1924 control module pin coding/implausible signal.
turkish citizenship
p1923 verify the engine control module's dtc memory (ecm 2)
Last edited by alidonka; 02-06-2022 at 06:00 AM.
Thread
Thread Starter
Forum
Replies
Last Post