The Sequel: SC install, DIY, Justatoy to Cattman
#211
Alright, at 9:04pm EDT I got the first injector out. Fuel spilling out, but what a satisfying smell!
Not sure how the heck I am going to get the furthest ones out, let alone any of them on the driver's side. It takes digital dexterity and strength.
Back to it, posting pics later. Keep the good mojo flowin'!
CATTMAN
Not sure how the heck I am going to get the furthest ones out, let alone any of them on the driver's side. It takes digital dexterity and strength.
Back to it, posting pics later. Keep the good mojo flowin'!
CATTMAN
As far as the smell of fuel.......YUP GREAT smell!
BTW....you may have found an easy way to clean the dirt/grit from your hands...FUEL,LOL!
Your arms will look like you have been scrappin' with a cat,LOL!!!
GL,
Stacy
#214
1 hour and 20 mins for all of them in and out for me....!
This was suppose to be the hardest part,they said,but NOT for me....I guess there is something to be said for 'small' hands,LOL!
Stacy
This was suppose to be the hardest part,they said,but NOT for me....I guess there is something to be said for 'small' hands,LOL!
Stacy
#215
Well, getting the injectors out was fine.
Getting them back into the fuel rail was a challenge, but doable.
However, getting them all seats- nope, struck out tonight.
However, since I got SOOO much done, I was totally fine to leave it alone and finish it during my next session.
So, with all the lines done, the pump in, and the injectors 25% done, I think I can see the light at the end of the tunnel.
Tonight I worked VERY casually, stopping to go online, eat, snack, sit for a few mins, from 6:30-11pm, so the total is now up to 19 hours.
Between working from 8-5, then turning the wrench an hour from home until midnight, I've not been the husband or father I want to be, so tomorrow at home would be a good idea.
In terms of difficulty? Well, it's certainly a challenging thing to undertake by yourself, with no lift, as a first-timer. I cannot recommend this as a DIY for everyone, to be sure. But if you really enjoy the journey more than the arrival, then there's really nothing preventing you from doing it.
Thanks, guys, for all the encouragement- I sure needed it!
CATTMAN
Getting them back into the fuel rail was a challenge, but doable.
However, getting them all seats- nope, struck out tonight.
However, since I got SOOO much done, I was totally fine to leave it alone and finish it during my next session.
So, with all the lines done, the pump in, and the injectors 25% done, I think I can see the light at the end of the tunnel.
Tonight I worked VERY casually, stopping to go online, eat, snack, sit for a few mins, from 6:30-11pm, so the total is now up to 19 hours.
Between working from 8-5, then turning the wrench an hour from home until midnight, I've not been the husband or father I want to be, so tomorrow at home would be a good idea.
In terms of difficulty? Well, it's certainly a challenging thing to undertake by yourself, with no lift, as a first-timer. I cannot recommend this as a DIY for everyone, to be sure. But if you really enjoy the journey more than the arrival, then there's really nothing preventing you from doing it.
Thanks, guys, for all the encouragement- I sure needed it!
CATTMAN
#216
Well, getting the injectors out was fine.
Getting them back into the fuel rail was a challenge, but doable.
However, getting them all seats- nope, struck out tonight.
However, since I got SOOO much done, I was totally fine to leave it alone and finish it during my next session.
So, with all the lines done, the pump in, and the injectors 25% done, I think I can see the light at the end of the tunnel.
Tonight I worked VERY casually, stopping to go online, eat, snack, sit for a few mins, from 6:30-11pm, so the total is now up to 19 hours.
Between working from 8-5, then turning the wrench an hour from home until midnight, I've not been the husband or father I want to be, so tomorrow at home would be a good idea.
In terms of difficulty? Well, it's certainly a challenging thing to undertake by yourself, with no lift, as a first-timer. I cannot recommend this as a DIY for everyone, to be sure. But if you really enjoy the journey more than the arrival, then there's really nothing preventing you from doing it.
Thanks, guys, for all the encouragement- I sure needed it!
CATTMAN
Getting them back into the fuel rail was a challenge, but doable.
However, getting them all seats- nope, struck out tonight.
However, since I got SOOO much done, I was totally fine to leave it alone and finish it during my next session.
So, with all the lines done, the pump in, and the injectors 25% done, I think I can see the light at the end of the tunnel.
Tonight I worked VERY casually, stopping to go online, eat, snack, sit for a few mins, from 6:30-11pm, so the total is now up to 19 hours.
Between working from 8-5, then turning the wrench an hour from home until midnight, I've not been the husband or father I want to be, so tomorrow at home would be a good idea.
In terms of difficulty? Well, it's certainly a challenging thing to undertake by yourself, with no lift, as a first-timer. I cannot recommend this as a DIY for everyone, to be sure. But if you really enjoy the journey more than the arrival, then there's really nothing preventing you from doing it.
Thanks, guys, for all the encouragement- I sure needed it!
CATTMAN
Great job! Not sure I would try it myself. I envy your enthusiasm
Jim
#217
Does anyone have any good suggestions on:
-how to best seat the injectors while they're in the fuel rail? Stacy said he used some kind of special lubricant which is engine safe?
-how to remove the black plastic wire hireness entirely from the fuel rail?
Thanks!
CATTMAN
-how to best seat the injectors while they're in the fuel rail? Stacy said he used some kind of special lubricant which is engine safe?
-how to remove the black plastic wire hireness entirely from the fuel rail?
Thanks!
CATTMAN
#218
Your posts scare the $hit out of me man and I`m not afraid of most DIY work usually... Make sure you know what you`re doing there.
#219
The fuel rail is held at the very back with a zap strap/wire tie which goes around the harness and plastic holder.Get a light and wire cutters and be careful NOT to JUST cut the strap!
Stacy
#220
Time and patience always wins in the end!
Stacy
#221
For the injector ring lube, I've always seem to seen that using a very light weight motor oil (5w-30, non-synthetic) is good. Will not swell the o-rings when seating. Just an ever-so-slight wipe on them.
#222
This is GREAT advice and will work!
Stacy
#225
Well tonight I started around 7, and ended around 10, again working very casually, stopping to go online, take pics, make a couple of calls, and eat dinner.
And I managed to resolved everything that was up in the air:
-corrected the issue of the hose to the front radiator on the driver's side by trimming it about a 1.5" so that the bent end, coming out of the tank, turns quickly, then down below and into the front of the car.
-removed the fitting on the front end of the driver's side crank case vent tube. This was not easy! When Stacy did it, he said he used a small screwdriver and some silicone lubricant. I suppose since my car is older, that hose was far too brittle to pry, so I used a hair dryer and a hose pick. I let the tube heat up really hot, so that it softened considerably, then I used a hose pick to get into the end, worked it all the way around the circumference, and was able to slowly twist it until it came out.
-seated the injectors on the passenger side! Woohooo!
-reattached the plastic wire harness holder, zip tied it back in place, and bolted down the fuel rail.
-removed the ECU, so I can FedEx it to VF-E tomorrow for reprogramming.
-reattached the horn/ horn bracket to the passenger side front bumper reinforcement.
Questions:
-The air intake temp sensor that I removed to access the fuel rail on the passenger side, how is it held in place? Looks like it just sits in the open, held by a round rubber grommet, but doesn't actually go inserted anywhere, is that right? If so, it would seem to be only measuring ambient temp back in the engine bay?
-Does anyone have any photos of where they ran the line from the pump up and over the transmission, and where/ how they secured it? I want to make sure I don't interfere with the gear linkage, and that's right above the pump.
Taking tomorrow off, and will be back at it first thing on Saturday, all day. So far, total working hours is up to 22.5 hours. I think about half or more of those have been spent "figuring things out", which means they could be eliminated if I ever did this again.
Left to do:
-remove stock injectors on driver's side
-install new larger injectors on driver's side
-install intercooler, fill lines with 50/50 peak lifetime, and test integrity by hooking up the pump to an external battery. If it's all working, I can reattach the wheel well liners, side radiator shroud, front bumper, headlights, and underpanels.
-begin mounting the SuperCharger, oil sharing plumbing, new air line, and belt.
-change oil and filter
-test it with my durametric to ensure good AF ratios and temps, etc.
There's light at the end of the tunnel!
CATTMAN
PS I've never even changed my oil or brake pads before. I've done mostly basic stuff, like mufflers, headers, cats, SSK, Dension, etc. Never done anything remotely this complicated or involved. My father once told me that I am not "mechanically inclined." He was wrong.
And I managed to resolved everything that was up in the air:
-corrected the issue of the hose to the front radiator on the driver's side by trimming it about a 1.5" so that the bent end, coming out of the tank, turns quickly, then down below and into the front of the car.
-removed the fitting on the front end of the driver's side crank case vent tube. This was not easy! When Stacy did it, he said he used a small screwdriver and some silicone lubricant. I suppose since my car is older, that hose was far too brittle to pry, so I used a hair dryer and a hose pick. I let the tube heat up really hot, so that it softened considerably, then I used a hose pick to get into the end, worked it all the way around the circumference, and was able to slowly twist it until it came out.
-seated the injectors on the passenger side! Woohooo!
-reattached the plastic wire harness holder, zip tied it back in place, and bolted down the fuel rail.
-removed the ECU, so I can FedEx it to VF-E tomorrow for reprogramming.
-reattached the horn/ horn bracket to the passenger side front bumper reinforcement.
Questions:
-The air intake temp sensor that I removed to access the fuel rail on the passenger side, how is it held in place? Looks like it just sits in the open, held by a round rubber grommet, but doesn't actually go inserted anywhere, is that right? If so, it would seem to be only measuring ambient temp back in the engine bay?
-Does anyone have any photos of where they ran the line from the pump up and over the transmission, and where/ how they secured it? I want to make sure I don't interfere with the gear linkage, and that's right above the pump.
Taking tomorrow off, and will be back at it first thing on Saturday, all day. So far, total working hours is up to 22.5 hours. I think about half or more of those have been spent "figuring things out", which means they could be eliminated if I ever did this again.
Left to do:
-remove stock injectors on driver's side
-install new larger injectors on driver's side
-install intercooler, fill lines with 50/50 peak lifetime, and test integrity by hooking up the pump to an external battery. If it's all working, I can reattach the wheel well liners, side radiator shroud, front bumper, headlights, and underpanels.
-begin mounting the SuperCharger, oil sharing plumbing, new air line, and belt.
-change oil and filter
-test it with my durametric to ensure good AF ratios and temps, etc.
There's light at the end of the tunnel!
CATTMAN
PS I've never even changed my oil or brake pads before. I've done mostly basic stuff, like mufflers, headers, cats, SSK, Dension, etc. Never done anything remotely this complicated or involved. My father once told me that I am not "mechanically inclined." He was wrong.
Last edited by Cattman; 01-21-2010 at 10:10 PM.