Broken radiator and disintegrating fans
#31
I layed the two module on a table, cut the wires (two big and two smalls) that goes to the car harness at 6 inches from the BTM.
I skinned the two big wires for about an inch and split the hairs in two groups, one group twisted toward the module and the other twosted together toward the harness. For the two big wires I used shrink tube over each connection, electrical tape, loom and electrical tape to isolate them individually. and then used a bigger loom over them to clip it to the rad shroud.
I skinned the two big wires for about an inch and split the hairs in two groups, one group twisted toward the module and the other twosted together toward the harness. For the two big wires I used shrink tube over each connection, electrical tape, loom and electrical tape to isolate them individually. and then used a bigger loom over them to clip it to the rad shroud.
#32
Glad it worked out. When I've done BMW fans different control wire lengths can be an issue (depending on the specifics of the vehicle make used as a substitute ) Sometimes they were too long other times a half inch too short. Curious how you lengthened the wire if these were too short. The wires on BMW fans are a heavy gauge that support 40 amps. Not easy to splice/solder and I'm not one for butt connectors. Moisture sealing is paramount for fan control wiring as any added resistance from wiring corrosion can modify the PWM signal interpretation (requested fan speed). When lengthening I've used marettes, then filled them with RTV then adequately taped to seal out moisture.
I just ordered the new version of this Ford based fan controller to see if it's feasible to swap into my Aston. It was only $22 USD.
Fan Control Module for Land Rover, Volvo, Ford & Jaguar
I just ordered the new version of this Ford based fan controller to see if it's feasible to swap into my Aston. It was only $22 USD.
Fan Control Module for Land Rover, Volvo, Ford & Jaguar
Last edited by kaj750; 05-09-2020 at 05:08 PM.
#33
Agreed that this would be helpful as I foresee the old/original units starting to fail as time goes on.
#34
Any chance you have a part number cross over to find a jag part that might be cheaper than the Aston part number? Similar to the deal with the radiator. I need a new condenser and dont like the 500 price tag of the aston part.
Thanks.
Thanks.
#38
I'm glad I found this thread
I just discovered (on my own) half the info here. I cam to post my findings, but you guys are 3 steps ahead.
On thing I found, if you have plastic problems, the end caps are available individually!
As of today, $38 each.
I'll get this car on the road, eventually.
On thing I found, if you have plastic problems, the end caps are available individually!
As of today, $38 each.
I'll get this car on the road, eventually.
Last edited by GT3 Chuck; 06-03-2023 at 08:33 PM.
#39
just a heads up for anyone else trying to purchase these, they didn’t fit my 2009 V8V roadster, they were very similar but about an inch too wide and the hoses didn’t use the quick disconnect fittings. Not sure if they work for earlier years or not.
Last edited by GT3 Chuck; 06-03-2023 at 08:32 PM.
#40
Glad it worked out. When I've done BMW fans different control wire lengths can be an issue (depending on the specifics of the vehicle make used as a substitute ) Sometimes they were too long other times a half inch too short. Curious how you lengthened the wire if these were too short. The wires on BMW fans are a heavy gauge that support 40 amps. Not easy to splice/solder and I'm not one for butt connectors. Moisture sealing is paramount for fan control wiring as any added resistance from wiring corrosion can modify the PWM signal interpretation (requested fan speed). When lengthening I've used marettes, then filled them with RTV then adequately taped to seal out moisture.
I just ordered the new version of this Ford based fan controller to see if it's feasible to swap into my Aston. It was only $22 USD.
Fan Control Module for Land Rover, Volvo, Ford & Jaguar
I just ordered the new version of this Ford based fan controller to see if it's feasible to swap into my Aston. It was only $22 USD.
Fan Control Module for Land Rover, Volvo, Ford & Jaguar
Have you tried installing the fan controller you quoted from before? It seems like from your posts and other users in this thread that the fans and ECU from Jaguar are easily plug and play. Thanks a lot for your contribution!!!
Last edited by GT3 Chuck; 06-03-2023 at 08:39 PM.
Thread
Thread Starter
Forum
Replies
Last Post