Shifter Kart Ready To Race!
#1
Shifter Kart Ready To Race!
2002 GP5 CR125cc shifter kart
This kart has not been raced in 2 years, only 3 seasons of use on it!
Has a 99 CR125 motor that was done by Mike Bellew, the top end was redone to be reliable by Carlson Bogan.
new 50mm axle, RLV silencer, T3 pipe, exhaust manifold with o-rings, programmable Vortex ignition, Vforce3 reed assembly with reeds in excellent shape, C&R radiator, new piston, ring, wrist pin, Modified Kehein carb with dual fuel pumps for pump around, and a new Tillett seat.
Frame, in great condition, this frame was just looked over for 7 hours by 2 guys at a local shop. It is perfectly straight, no cracks.
Spares...
Numerous used front and rear brakes pads
Numerous brake shims
Numerous clutch friction discs and floaters
1 17 tooth driver gear
1 23 tooth sprocket
3 sidepods
3 noses
1 floorpan
1 NEW coil
2 carb needles(CCJ, CGJ)
4 pilot jets(48, 50, 52, 55)
9 main jets(155, 158, 162, 165, 168, 170, 172, 175, 178)
1 exhaust manifold
1 intake manifold
1 intake manifold gasket
1 set of used Bridgestone YHC tires
1 steering rod with steering wheel and clutch lever
5 front spindles
2 front brake rotors and hubs
2 steering connecting rods
1 rear brake rotor and brake hub for 50mm axle
1 rear brake rotor and brake hub for 40mm axle
Extra brake caliper hardware
2 used Vforce 3 reeds
3,599 obo for everything!
This kart has not been raced in 2 years, only 3 seasons of use on it!
Has a 99 CR125 motor that was done by Mike Bellew, the top end was redone to be reliable by Carlson Bogan.
new 50mm axle, RLV silencer, T3 pipe, exhaust manifold with o-rings, programmable Vortex ignition, Vforce3 reed assembly with reeds in excellent shape, C&R radiator, new piston, ring, wrist pin, Modified Kehein carb with dual fuel pumps for pump around, and a new Tillett seat.
Frame, in great condition, this frame was just looked over for 7 hours by 2 guys at a local shop. It is perfectly straight, no cracks.
Spares...
Numerous used front and rear brakes pads
Numerous brake shims
Numerous clutch friction discs and floaters
1 17 tooth driver gear
1 23 tooth sprocket
3 sidepods
3 noses
1 floorpan
1 NEW coil
2 carb needles(CCJ, CGJ)
4 pilot jets(48, 50, 52, 55)
9 main jets(155, 158, 162, 165, 168, 170, 172, 175, 178)
1 exhaust manifold
1 intake manifold
1 intake manifold gasket
1 set of used Bridgestone YHC tires
1 steering rod with steering wheel and clutch lever
5 front spindles
2 front brake rotors and hubs
2 steering connecting rods
1 rear brake rotor and brake hub for 50mm axle
1 rear brake rotor and brake hub for 40mm axle
Extra brake caliper hardware
2 used Vforce 3 reeds
3,599 obo for everything!
#7
Trending Topics
#14
Originally Posted by Tyler2000S4
How fast does it go? Just curious...
0 - 60mph in 3.4 seconds
For the top speed is probably around 115 without a draft and close to 140 with a draft.
Here is a helmet cam from driving around some streets. With the gearing in this video it was only going about 80, and the motor was running very rich (made a lot less power, but got a lot more oil). Also the tires had almost no grip because it was so cold out, this made 1st gear spin the tires which doesn't happen when it's warm.
http://www.youtube.com/watch?v=gx7Zw4Opnjs
Last edited by E36M; 03-17-2007 at 05:21 PM.