996 NB Fitment Question -- Wheel experts come on in!
#1
996 NB Fitment Question -- Wheel experts come on in!
The attached chart shows the fitment for C2 NB cars.
If a rim from a WB car in the rear was 19 x11.0 and the offset is 39mm compared to the required 52mm on a NB could this be remedied with a spacer? i.e my fitment shows a required offset of 52mm and on the WB the offset required is only 39mm? Or do I have this backwards? Anybody with experience please chime in.
FrontSizeOffsetFinishBolt PatternList
19 x 8.5 45 Silver w. Polished lip 5 x 130.00
RearSizeOffsetFinishBolt PatternList
19 x 11.0 52 Silver w. Polished lip 5 x 130.00
19 x 11.0 64 Silver w. Polished lip 5 x 130.00
Thanks
If a rim from a WB car in the rear was 19 x11.0 and the offset is 39mm compared to the required 52mm on a NB could this be remedied with a spacer? i.e my fitment shows a required offset of 52mm and on the WB the offset required is only 39mm? Or do I have this backwards? Anybody with experience please chime in.
FrontSizeOffsetFinishBolt PatternList
19 x 8.5 45 Silver w. Polished lip 5 x 130.00
RearSizeOffsetFinishBolt PatternList
19 x 11.0 52 Silver w. Polished lip 5 x 130.00
19 x 11.0 64 Silver w. Polished lip 5 x 130.00
Thanks
#2
You have it backwards...the Higher the offset the further in the wheel will sit, and the lower the further out...so if your car requires a ET+52 and you put on a wheel that is an ET+39, then the wheels will be sticking out 13mm...a 1/2" inch basically.
Hopefully this answers your question.
Regards,
Jim
Hopefully this answers your question.
Regards,
Jim
#5
https://www.6speedonline.com/forums/...turbo-c4s.html
Hi Jim, I was enquiring about the fitment of the above rims. In general I am looking for a five spoke design, maybe with a dish. 19 inches.
My car is a 996 C2.
Hi Jim, I was enquiring about the fitment of the above rims. In general I am looking for a five spoke design, maybe with a dish. 19 inches.
My car is a 996 C2.
#7
If your car is the one in your avtar it appears to be an 02>+ C2...if so you can run a 19x8.5 front using an ET+40-50MM using a 235/35-19 tire, and for the rear you have 2 options...you can run a 19x10.0 with a ET40 using a 275/30-19 tire, or you can run a 19x11.0 with a ET+52 and use a 315/25-19 tire.
We have a few 5 spoke design wheels that we offer...attached is an example of a 997 with a set of our NUTEK 501 wheels, the finish was a full brushed finish on the center and outer, and black ceramic on the spoke face and black ceramic pinstripe.
Feel free to email me directly and I will send you some other examples to review jim@nutekwheels.com
Regards,
Jim
We have a few 5 spoke design wheels that we offer...attached is an example of a 997 with a set of our NUTEK 501 wheels, the finish was a full brushed finish on the center and outer, and black ceramic on the spoke face and black ceramic pinstripe.
Feel free to email me directly and I will send you some other examples to review jim@nutekwheels.com
Regards,
Jim
Thread
Thread Starter
Forum
Replies
Last Post
PelicanParts.com
GT3/GT2/GT Vendor Classifieds
0
08-20-2015 02:37 PM
PelicanParts.com
996 Vendor Classifieds
0
08-18-2015 03:45 PM
PelicanParts.com
996 Turbo Vendor Classifieds
0
08-18-2015 03:43 PM
PelicanParts.com
GT3/GT2/GT Vendor Classifieds
0
08-18-2015 03:42 PM